We definitely carry those! For those parts, you need 2x of the # RG04-080 and 1 of the # DC250L-DCRP. I went ahead and attached helpful demo videos of these products for your convenience. view full answer...
The bearings we have, # L44643, and the associated race is # L44610. The cotter pin is # 165649. The dust cap associated with hubs that take these bearings is # RG04-020 for a pair. The seal on the other hand is an odd size. There isn't a bearing kit that has the seal that you need and it is an odd size that we do not carry. But it is readily available at auto parts stores.
I know that a kit would make things a lot easier but in this situation there isn't a kit that has the seal and dust... view full answer...
A trailer hub assembly will use an inner bearing and race, an outer bearing and race, a grease seal, a cotter pin, and either a dust cap or a bearing protector. I am including a picture that will show where the part numbers are located and the areas that you will need to measure if your parts do not have part numbers etched on them.
There is only one grease seal on the spindle and it is located on the rear of the hub assembly (see picture).
Looking up the grease seal number CR12427 on... view full answer...
For your 2017 Karavan KB2200 boat trailer you will need the following parts for rebuilding your hubs.
Inner Bearing # L68149
Outer Bearing # L44649
Inner Race # L68111
Outer Race # L44610
Grease Seal # TMK29ZR
Cotter Pin # 165649
If the Sure Lube cap is damaged during removal you can replace them with the superior Bearing Buddy Bearing Protectors # BB1980A-SS. view full answer...
To determine which Bearing Buddy you need, you'll either need to measure the hub bore (inside diameter of hub where grease cap inserts) or provide me with the outer wheel bearing reference number. With the bearing number, I can find the corresponding race for the bearing. The race's outside diameter will match the diameter of bearing protector you'll need.
I would recommend replacing the grease seal as well. Use a double lip seal to help prevent blow-out. To determine which seal you'll... view full answer...
If your races are # L44610, which they almost certainly are, you will want the following parts:
Bearings:
Inner bearing: # L44649
Outer bearing: # L44649
Grease seal: # 10-9
Outer diameter: 1.987"
Inner diameter: 1.5"
Grease cap: 1.986"
But just to make sure you may want to measure your spindle to be sure bearings will fit and check races and hub for their part number.
I have included a picture that shows the measurements needed for a spindle,... view full answer...
Based on your inner bearing being L68149 and outer bearing indicating L44649, I recommend Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles # 84545UC1-EZ as long as your wheels have a 5 on 4-1/2 inch bolt pattern.
This hub is designed for use on trailer idler axles. Fits 3,500-lb E-Z Lube axles with #84 spindles. Inner bearing # L68149 and race, outer bearing # L44649 and race, grease seal, grease cap, wheel bolts, and lug nuts included.
We also have Bearing Kit for #84 Spindle,... view full answer...
In order to determine which size bearings, races, and grease seals you have, you will need to take apart your hub. The bearings and races will have numbers marked on them that you can cross-reference to determine which parts will work for replacements. If the numbers are worn off and impossible to read, you will need a high-precision caliper to measure the inner and outer diameters of your bearings and races because they have tight tolerances down to thousandths of an inch.
You can determine... view full answer...
While the # L68149 most likely corresponds to the inner bearing number of your hubs. If this is the case, you have either a 3.5k or a 4.4k axle.
In order to know absolutely sure, you need to know the corresponding outer bearing number or the inner and outer diameter of the grease seal. You most likely need to wipe away the grease in order to reveal the outer bearing number. In order to accomplish this, I recommend using calipers like the 4" Carbon Fiber Digital Caliper # PTW80157.
I... view full answer...
If the bearing numbers, # L44649 and # L68149, along with the seal number all match yours then you have a # 84 spindle and the # BK2-100 bearing kit is what you need.
This kit includes the tang washer to use with EZ Lube spindles as well. view full answer...
The Kodiak XL ProLube Kit # XLPROLUBE1980KIT is designed to work with most 3,500lb axles. It includes 2 oil seals for a 1.72" spindle, 2 caps for a 1.98" hub bore and a bottle of oil. I recommend getting new bearings and races which I will list below.
Inner Bearing # L68149
Inner Race # L68111
Outer Bearing # L44649
Outer Race # L44610
Tang Washer # 5-101
Cotter Pin # 165649
The Seal Puller # PTW1219 and Install Kit # PTW83020 will make replacing the components easier. I do recommend... view full answer...
My technical contact at Dexter let me know that your axle # LN 122800457 uses Dexter Trailer Hub Assembly # 8-259-5UC1. This hub assembly comes with the inner and outer bearings, races, seal, grease cap, wheel bolts and lug nuts. The inner and outer bearings are the same # L44649. The race is # L44610.
If you have this axle on a Triton Trailer then, originally those hubs had a corrosion resistant zinc finish whereas these replacement hubs are painted.
I have attached a brief video review... view full answer...
We do have the parts you're needing, but the Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs # KHR10D only comes with the races included; the bearings, grease seals and caps are not included and must be purchased separately.
You can use the Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100 which will give you the bearings to fit in these hubs and also includes the tang washer and cotter pin. The only other part you would require... view full answer...
With axle 8-258, your bearings are either # L44643 or # L44649. # L44643 bearings have an inner diameter of 1 inch, while bearings # L44649 have an inner diameter of 1.063 inches. You can locate the bearing numbers on the bearings themselves, or you can measure the diameter using the image I've attached.
We offer two hub assembly kits with # L44643 bearings. Item # 8-258BTUC1 is the standard hub assembly kit, which includes lug nuts, inner bearings and race, outer bearings and race, grease... view full answer...
Yes. The Dexter Trailer Idler Hub Assembly # 84545UC1-EZ can be used with the Timbren Heavy Duty Axle-Less Trailer Suspension # ASR2KHDS03 since they both use:
Bearings: # L68149 inner, # L44649 outer
Races: # L68111 inner, # L44610 outer
Seal: 10-19 part # RG06-050 (pair)
The # 84545UC1-EZ has a 5 on 4-1/2 bolt pattern and comes with the bearings, races, seals, grease cap, wheel bolts, and lug nuts included. view full answer...
To determine the correct bearings, races, and seals for your 2007 Rolls Rite 24K trailer you will need to remove the wheel and hub from your trailer and use the part numbers off of the bearings, races, and seals that you have. There is not a listing for bearings on a particular trailer, because the trailer manufacturers are always changing brands of axles on the same trailers, which could use different size bearings, races, and seals.
The washer and nut will depend on what size and type... view full answer...
Sounds like you will need the # 15123 bearing and # 15245 race for that bearing.
For the # 25580 bearing, you'll need the # 25520 race.
For the oil seal you would need part # 9103309 which is the exact same as your 412920.
We do not have a full kit of this so they are all sold separately.
I have linked all the above mentioned products to this page for your convenience. view full answer...
When replacing the disk brake rotors on your trailer it is recommended that you also replace your bearings, races and seals at the same time. This will ensure that all components are new and in good order and will prevent the need to dismantle your trailer again to replace an older part that may wear out before others.
The bearing kit for this rotor is part # BK3-100. I have included an article that covers the process of replacing bearings, races and seals on a trailer hub.
The Kodiak... view full answer...
When it comes to replacing your hub and drum that has an outer bearing # L44649 and an inner bearing # L68149 The Dexter Trailer Hub and Drum Assembly for 3,500-pound E-Z Lube Axles - 10 inch Diameter - 5 on 4-1/2 # 84546UC3 will work for you.
This hub and drum has an E-Z Lube-compatible grease cap that makes it easier to lubricate the bearings. The grease cap flange diameter is 1.986 inches and has a wheel bolt diameter of 1/2 inch. All bearings, races, grease seal, grease cap, wheel... view full answer...
Tapered roller bearing # LM11949 is typically used in agricultural hubs and mates with race # LM11910. We do offer these parts the correct grease seals # CE16305A to match your dimensions but we do not offer any hubs that use this specific bearing as both the inner and outer bearing.
Your best bet is to replace the entire axle with an up-to-date kit that includes everything, such as Dexter 3500-lb axle # 35545I-EZ-89 as an example. This 89-inch axle has spring seats spaced at 74-inches... view full answer...
Go To Results